Fixed Rooflights > GV Walk On Flushglaze

Gallery (Click to enlarge)

Introduction
The Flushglaze Walk on rooflight offers the same characteristics as a standard flushglaze rooflight in that it uses the same profile however slightly larger. The walk on Flushglaze rooflight can be tailored to meet many shapes and sizes from square, rectangular, circular, triangular and many other bespoke configurations.

The Flushglaze is a very low profile system based on car windscreen technology, the glass being structurally bonded and triple sealed into the framework with no internal visible framework on single units (3m²) for larger units see Modular Flushglaze

Standard and bespoke sizes are available, stock rooflights are offered on a 48 hour delivery basis bespoke are typically on a 4/6 week lead time dependent on your requirement. Lead times will be advised on all quotations undertaken.

** The Walk on Flushglaze Rooflight can be installed flush with decking and also comes as an internal walk on glass panel or panels**

Standard Sizes (48 hour delivery)
All sizes refer to Overall weathered upstand dimensions
1500mm x 1000mm
2000mm x 1000mm
(All stock sizes come in our standard RAL7015 Slate Grey Outer)

Specifications (for Single piece units only, see modular for multiple panels)
Maximum Kerb Span/Width: 4000mm
Minimum Kerb Span/Width: 450mm
Standard Unit Guide Weight (daylight spec only): 75kg / sq m
Circular Maximum Kerb Span/Width: 2000mm
Circular Minimum Kerb Span/Width: 600mm
Kerb Width Minimum: 75mm
Kerb Height Minimum: 150mm
Minimum Kerb pitch: 1º
Domestic Floor Load Only – UDL = 1.8KN/m²
(Additional Concentrated Load = 1.4KN Point Load)

Glass Specification:-
Standard Glass Spec
21.5mm Clear toughened laminated heat soak tested outer - 16mm ARGON filled cavity - 6mm low E inner

Various glass specifications can be provided for if there is a requirement for greater loading capability and will require an increase in the double glazed unit size.

Colour- all our rooflights are Powder coated to either RAL7015 Grey or RAL9010 White, alternative paint specifications are available however these can effect both price and lead times.

Wall Abutment Detail – In circumstances where the rooflight is to abut a wall rather than sit down over a kerb a wall abutment detail can be incorporated on upto three sides of the Flushglaze Rooflight to allow fixing direct into a wall please ask for drawing reference:- 402/ASS/008

Warranty – the Flushglaze Rooflight comes with a standard 5 year warranty.

Type: Flushglaze Walk on range
Glazing Details: 43.5mm Double glazed units comprising 21.5mm clear toughened laminated outer pane, 16mm airspace and 6mm clear toughened low E inner pane. Units to have silicone edge seal.

Frame: Extruded aluminium cill profile, grade 6063 T6
Finish: Polyester Powder Coated.
Colour: White RAL9010 matt or RAL7015 matt as standard.
Kerb: 75mm wide up-stand to all sides as manufacturer’s recommendation. Minimum 1 degrees fall.
Other requirements: External glazing surfaces to be flush with no flashings or water ponding obstructions/dirt traps on the glass surface

Installation
Installation onto prepared roof apertures and up-stands is simple, each rooflight is supplied assembled, packaged with instructions and fitting kit. Either follow our detailed assembly instructions, or opt for a Glazing Vision installation service. All standard sizes are factory pre-assembled and delivered in one completed unit.

An on site lifting facility will be required to locate the heavier units to the roof location.

Please remember when requesting a quote, specify the outside dimensions of the opening/kerb, you should then make an allowance of approximately 150mm for inside dimensions subject to chosen internal finishes dimension.

Resources
Resource Centre [For registered users only]
Request a Quote
National Building Specifications (NBS): MS Word Format | Plain text format